+86 574 6260 2751
Home / News / Industry News / How to install and use the fiber optic cable junction box?

How to install and use the fiber optic cable junction box?

In view of the current high occupancy rate of the aggregation equipment room, in order to reduce the impact of the relocation of the leased equipment room on the optical cable network, an optical delivery box should be set up in front of the important rental equipment room; Places entering and exiting lines, not easily affected by external damage and natural disasters, but also in line with urban planning and do not hinder urban traffic, do not affect the view of the city. The optical switch box of the access backbone layer should be set at the intersection of the main road or street, so as to facilitate the extension and coverage of the optical cable to the distribution layer; the capacity of the optical switch box should be comprehensively considered according to the network level and business needs. The fiber distribution box should be mainly 576 cores; for the existing small-capacity optical distribution box (below 288 cores), if it cannot meet the business needs, it should be expanded, and if it cannot be expanded, a large-capacity optical distribution box should be used instead.
Installation specification of outdoor fiber distribution box and base 1. The installation of the transfer box must be firm, firm, safe and reliable, the box body should be horizontal and vertical, and the box door should have a good locking device. 2. The junction box should be assembled with complete spare parts and firm terminals. 3. The signs such as the number of the junction box, the number of the optical cable and the core should be correct, complete, clear and tidy. The selection of the installation location of the floor-mounted transfer box should be matched with the transfer box base, manhole and hand hole. The height of the base can be determined according to the terrain of each region. Generally, the height of rainproof is 300mm. 4. The distance between the base of the handover box and the manhole and hand hole is generally required not to exceed 10 meters, but it must be required to lay galvanized steel pipes or plastic pipes, and small passages shall not be used. 5. Foundation pouring of the handover box: The foundation of the handover box is required to be a concrete foundation with a thickness of 10cm and 150#, and the sundries should be cleaned before pouring the foundation. 6. Brick masonry for the foundation of the junction box: the masonry is made of 100# mortar, and the mortar saturation of the brick masonry is not less than 80%. The surrounding corners, bottom edges and windows need to be painted with eight characters, and the width of the wall is 24cm. 7. The base mortar plastering surface: the mortar with the label of 100# is generally used for plastering without special circumstances. The thickness of the inner plastering reaches 1.5cm, and the thickness of the outer plastering reaches 2cm. No hollow, no flying spurs, no breakage. If there are special circumstances such as flooding around the well, it is necessary to increase the cement label and thicken the outer batch or add a leak-proof agent. 8. Pre-embedded iron in the base: The specifications and positions of the nails conform to the design regulations. There are pre-cast anchor screws (bolts M12X30) on the four corners of the base of the junction box to fix the junction box. And reserve a rectangular hole (822mm×622mm) in the center of the base as the entrance and exit of the optical cable. 9. The contact between the transfer box and the base should be wiped with "eight-character gray" to prevent water from entering.
fiber optic outlet box

You May Also Like

  • Horizontal 96 Core Optic Fiber Joint Closure | HF96-8B
    Horizontal 96 Core Optic Fiber Joint Closure | HF96-8B
  • Horizontal 8 Core Optic Fiber Joint Closure | 8BR
    Horizontal 8 Core Optic Fiber Joint Closure | 8BR
  • 16 Cores 16 Ports Horizontal Fiber Optic Joint Closure | HF96-16B
    16 Cores 16 Ports Horizontal Fiber Optic Joint Closure | HF96-16B
  • 24 Core 24 Ports Horizontal FOSC Butt Closure | HF96-24A
    24 Core 24 Ports Horizontal FOSC Butt Closure | HF96-24A
  • Mini 2 FO Drop Cable Joint Closure | GJS-H1102
    Mini 2 FO Drop Cable Joint Closure | GJS-H1102
  • Comapct 1 Input 2 outputs Drop Cable Closure | GJS-H1203
    Comapct 1 Input 2 outputs Drop Cable Closure | GJS-H1203
  • 96FO In-line Fiber Optic Splice Closure | GJS-H2012
    96FO In-line Fiber Optic Splice Closure | GJS-H2012
  • 2 In 2 Out Inline Closure 96FO IP68 | GJS-H2201
    2 In 2 Out Inline Closure 96FO IP68 | GJS-H2201
  • 4 Core Plastic Material Outdoor Fiber Optic Distribution Box | FDB-4A
    4 Core Plastic Material Outdoor Fiber Optic Distribution Box | FDB-4A
  • FTTH 6 core fiber optic distribution box IP65 | FDB-6B
    FTTH 6 core fiber optic distribution box IP65 | FDB-6B
  • FTTH Outdoor 8 Core Optical Fiber Distribution Box | FDB-8A
    FTTH Outdoor 8 Core Optical Fiber Distribution Box | FDB-8A
  • Fiber Optic Wallmount Distribution Enclosure ODB for FTTH Project 8 Core | FDB-8B
    Fiber Optic Wallmount Distribution Enclosure ODB for FTTH Project 8 Core | FDB-8B